Table of Contents
- Quick Comparison: 5 Best Wireless Backhaul Equipment for 2026
- 1. Mimosa A6 Access Point: Best for High-Capacity Point-to-Multipoint Backhaul Equipment
- 2. Mimosa B24: Best for Interference-Free 24 GHz Links
- 3. Mimosa C6x: Best Value Point-to-Point Wireless Bridge Equipment
- 4. NetBox 5 ax: Best Flexible AP, CPE, and Point-to-Point Radio
- 5. LHG XL 5 ax: Best Budget Long-Range CPE
- Wireless Backhaul Throughput and Range: What the Specs Actually Mean
- Wireless Backhaul Frequency Planning: 5 GHz vs 6 GHz vs 24 GHz
- Frequently Asked Questions
Last Updated: October 17, 2026
Quick Comparison: 5 Best Wireless Backhaul Equipment for 2026
Wireless backhaul is the link that carries traffic from an access network back to the core, and choosing the wrong radio for that job is the most expensive mistake we see in fixed wireless deployments.
The short answer: match the radio to the link, not to the datasheet headline. A 24 GHz point-to-point shot and a 5 GHz multipoint sector solve completely different problems.
| Radio | Best For | Frequency Band | Stated Throughput | Antenna | Price (USD) |
|---|---|---|---|---|---|
| Mimosa A6 | High-capacity point-to-multipoint | 5.1-6.4 GHz | Up to 7 Gbps | 8x8 MU-MIMO | $2,010.00 |
| Mimosa B24 | Interference-free short links | 24 GHz | Gigabit class | Integrated | $695.00 |
| Mimosa C6x | Value point-to-point and PTMP | 5/6 GHz | 2.0 Gbps PTP, 1.75 Gbps PTMP | Adaptable | $192.00 |
| NetBox 5 ax | Flexible AP, CPE, or PTP | 5 GHz Wi-Fi 6 | Not published | RP-SMA, antenna optional | $109.00 |
| LHG XL 5 ax | Budget long-range CPE | 5 GHz Wi-Fi 6 | Not published | 27 dBi dish | $119.00 |
1. Mimosa A6 Access Point: Best for High-Capacity Point-to-Multipoint Backhaul Equipment
The A6 is a radio for single sectors serving many subscribers at once. It is a 5.1-6.4 GHz access point rated for up to 7 Gbps, built around 8x8 MU-MIMO, 1024-QAM, 8-stream beamforming, and up to 160 MHz of bandwidth.
Where it falls short: at $2,010.00 it is the most expensive radio here by a wide margin, and it only earns that price in dense multipoint work. Pair it with the C6x client radio to reach gigabit subscriber speeds.
2. Mimosa B24: Best for Interference-Free 24 GHz Links
Crowded 5 GHz spectrum can impact wireless backhaul throughput, and the B24 operates in the less crowded 24 GHz band.
The trade-off is physics: 24 GHz links need clean line of sight and shorter paths. If your two endpoints are close and unobstructed, the B24 at $695.00 is a clean answer. If they are not, look elsewhere in this list.
3. Mimosa C6x: Best Value Point-to-Point Wireless Bridge Equipment
For integrators, the C6x offers a strong value proposition. It delivers up to 1.75 Gbps in point-to-multipoint and 2.0 Gbps in point-to-point mode, carries an IP67 rating, and works across adaptable range options.
At $192.00 it offers strong price-performance in this group. The honest limitation is that it is a workhorse, not a capacity monster: for a dense sector, step up to the A6.
4. NetBox 5 ax: Best Flexible AP, CPE, and Point-to-Point Radio
One radio, three jobs. The NetBox 5 ax is a dual-chain outdoor Wi-Fi 6 device that runs as an access point, a CPE, or a point-to-point link, with RP-SMA connectors so you can add an omnidirectional antenna or a directional dish as the site demands.
What most guides miss is how much the antenna choice changes the outcome. The same $109.00 board is a modest AP with one antenna and a long-range bridge with another.
5. LHG XL 5 ax: Best Budget Long-Range CPE
The LHG XL 5 ax is designed for long-distance links on a budget. It is a Wi-Fi 6 outdoor CPE with a 27 dBi integrated dish, built for point-to-point links over long spans, and it lists at $119.00, the same price as the previous generation.
A common mistake is buying the XL for short links where its narrow beam makes alignment fussy. For shorter spans, the standard 24.5 dBi LHG 5 ax at $99.00 is easier to aim.
Wireless Backhaul Throughput and Range: What the Specs Actually Mean
Published throughput figures describe the radio link, not what your clients will see.
The mechanism is worth understanding because it drives every equipment decision. Stated throughput is a physical-layer (PHY) rate: it assumes the highest modulation the radio supports, the widest channel the band allows, and a signal-to-noise ratio clean enough to sustain both. Every one of those assumptions is a lever that real deployments pull in the wrong direction:
- Channel width. A 160 MHz channel carries roughly twice the PHY rate of an 80 MHz channel, but it also occupies twice the spectrum and is twice as likely to overlap a neighbor. In congested 5 GHz, an 80 MHz channel often delivers more usable throughput than a 160 MHz channel that keeps retrying.
- Modulation and coding. 1024-QAM and 8-stream beamforming only engage at high SNR. As distance grows and SNR falls, the radio steps down through lower modulation schemes, and usable throughput can drop by half or more before the link ever disconnects.
- Interference and noise floor. A raised noise floor forces the radio to spend airtime on retries. Two links with identical signal strength can deliver very different throughput if one sits in a clean channel and the other shares spectrum with a dozen neighbors.
A repeatable way to compare radios before you buy: test the same link with the same channel width, the same distance, and the same client load, and record throughput at several SNR levels rather than one.
Range works the same way. Treat the published range figure as a best case for a clear path, then subtract for foliage, walls, and rooftop clutter.
Wireless Backhaul Frequency Planning: 5 GHz vs 6 GHz vs 24 GHz
Frequency planning decides whether your wireless backhaul survives contact with reality. For broader guidance on spectrum rules, see the FCC equipment authorization and spectrum guidance.
A practical approach: use 24 GHz for short, critical hops, 6 GHz where you need clean wide channels, and 5 GHz for everything else. Plan channels across every sector before you mount a single radio, not after.
Match the band to the backhaul scenario
The keyword covers more than one kind of link, and the right band changes with the job. Use this as a starting decision guide:
- Home mesh and whole-home coverage. Consumer mesh kits typically use 5 GHz or 6 GHz for the backhaul between nodes, with tri-band systems dedicating one radio to backhaul so client traffic does not compete with it. Dedicated backhaul beats shared backhaul when many devices are active at once; shared backhaul is cheaper and fine for lighter loads. For most homes, a tri-band system with a dedicated 6 GHz backhaul is the cleaner choice when the budget allows.
- Detached buildings on one property. A point-to-point bridge between a house and a garage, barn, or shop is a short, usually clear link. 5 GHz with directional antennas is the workhorse here; 24 GHz is a good fit when the path is short and unobstructed and you want to escape neighborhood congestion.
- Rural and long-distance links. Distance favors lower frequencies and higher-gain directional antennas. 5 GHz with a large dish (such as the 27 dBi integrated dish on the LHG XL 5 ax) is the common pattern; 6 GHz can help where you need clean wide channels over moderate spans, but reach is shorter than 5 GHz.
- Business and multi-sector networks. Dense sectors need capacity planning, not just band choice. Use 5 GHz or 6 GHz for the access layer, reserve 24 GHz for short critical hops between buildings, and plan channel reuse across every sector so adjacent radios do not overlap.
Plan channels before you mount radios
Channel planning is where most deployments either succeed quietly or fail loudly. A few mechanics that matter:
- Reuse across sectors. Assign non-overlapping channels to adjacent sectors and access points. In 5 GHz, the available non-overlapping channels are limited, so a multi-sector site needs a reuse plan, not ad-hoc channel picks.
- Width versus congestion. Wider channels carry more throughput but occupy more spectrum. In a crowded area, narrower channels often deliver more usable throughput because they retry less.
- Alignment and Fresnel zone. For point-to-point links, alignment is part of frequency planning: a misaimed dish raises the noise floor and forces lower modulation. Clear the Fresnel zone at the midpoint, not just the visible line.
- Security and management. Compare encryption, access controls, firmware support, and remote management before you commit to a platform. VLAN and network-segmentation options matter for business networks that carry multiple services over one backhaul. A radio that is easy to manage remotely saves truck rolls on rural links.
Total cost of ownership, not just sticker price
The equipment price is only part of the cost of a backhaul link. Budget for mounting hardware, cabling, PoE injectors, power, and maintenance, and factor in the labor to align and re-aim a link after construction or foliage changes. A cheaper radio that needs more frequent site visits can cost more over its life than a slightly more expensive one that holds alignment and manages cleanly.
Frequently Asked Questions
What is wireless backhaul equipment?
Wireless backhaul equipment is the radio and antenna hardware that carries traffic between a network's edge and its core without fiber or cable. In fixed wireless deployments it links access points, towers, and client sites. Options range from compact CPE radios like the SXTsq 5 ax at $65 to high-capacity access points like the Mimosa A6 at $2,010. The right pick depends on whether you need a point-to-point bridge, a point-to-multipoint sector, or a long-range client radio.
What is the difference between wireless backhaul and mesh Wi-Fi backhaul?
Mesh Wi-Fi backhaul connects consumer satellite nodes inside one home, usually over shared 5 GHz or 6 GHz channels. Wireless backhaul equipment for ISPs and integrators uses dedicated outdoor radios, directional antennas, and licensed or unlicensed bands to move traffic across kilometers. Mesh kits optimize for easy setup; backhaul radios optimize for throughput, range, and interference handling. That is why a C6x can deliver up to 2.0 Gbps in point-to-point mode while a mesh node shares airtime with client devices.
How much throughput can a wireless backhaul link deliver?
It depends on the radio and mode. The Mimosa C6x is rated up to 1.75 Gbps in point-to-multipoint and 2.0 Gbps in point-to-point. The A6 access point is rated up to 7 Gbps with 8x8 MU-MIMO and 160 MHz channels. Real-world throughput lands lower once you account for channel width, distance, interference, and client load, so plan capacity with headroom rather than sizing to the headline number.
What factors affect wireless backhaul range and reliability?
The biggest factors are line of sight, antenna gain, frequency band, and interference. Higher-gain antennas such as the 27 dBi LHG XL 5 ax extend reach, while lower bands like 5 GHz handle rain fade better than 24 GHz. Fresnel zone clearance, mounting height, and precise alignment matter as much as the spec sheet. A clean 5 GHz channel with a 24.5 dBi antenna often outperforms a crowded link with better hardware.
How do you plan a point-to-point wireless backhaul link?
Start with a site survey to confirm clear line of sight and Fresnel zone clearance, then choose a band based on distance and interference. Use a link planner to estimate signal strength and throughput at your chosen antenna gain. For a link up to 30 km, the NetBox 5 ax paired with a mANT30 PA antenna is one option. Align both ends carefully, verify signal before tightening mounts, and document channel plans so future links do not overlap.
Picking backhaul radios one SKU at a time is how networks end up with mismatched links and mystery outages. BI-DISTRIBUTION supplies the full Mimosa and MikroTik backhaul range and backs it with network design, RF planning, and frequency coordination, so the radio you buy fits the link you are actually building. Get started with BI-DISTRIBUTION and spec your 2026 backhaul plan around radios that match the job.


